How to replace the Webcam for OMEN by HP 15-dg Series Gaming Laptop
Print

How to replace the Webcam for OMEN by HP 15-dg Series Gaming Laptop


Star InactiveStar InactiveStar InactiveStar InactiveStar Inactive
 
BEFORE YOU BEGIN
  1. If the unit contains heated components, wait until the components have cooled off before proceeding.
  2. Put on your electrostatic discharge (ESD) wrist or shoe strap to avoid damaging any circuitry. 
  3. Place an ESD mat on a suitably grounded surface, and then place the unit on the mat.
  4. Remove any devices from the unit being serviced, such as CD-ROMs, SD Memory Card ...etc.
  5. Power off the unit and any peripheral devices that are connected to it.
  6. Disconnect the power cord from the electrical outlet and then from the unit.
  7. When a unit is plugged into an AC power source, voltage is always applied to the unit.
  8. You must therefore disconnect the power cord from the power source before opening the unit.
  9. Disconnect all peripheral device cables from the unit.
TOOLS USED IN REMOVAL AND REPLACEMENT
Ensure that you have the tools you need before you begin. These should include:
  • Small, Phillips-head (P1 and P0) screwdriver
  • Small, flat-bladed screwdriver or a flat-bladed alignment tool
  • Tweezers
  • Electrostatic discharge (ESD) wrist or shoe strap
  • Smooth jaw, bent-tipped needle nose pliers (optional)
  • Small, smooth-tipped needle nose pliers (optional)
  • Flashlight (optional)
  • If worn or damaged screwdriver tips are used, the small screw heads could become stripped.
DISASSEMBLY TIPS.
  1. Ensure that you take the following precautions when disassembling a unit
  2. Label each cable as you remove it, noting its position and routing. This will make replacing the cables much easier and will ensure that the cables are rerouted properly.
  3. Keep all screws with the component removed, if applicable. The screws used in each component can be of different thread sizes and lengths. Using the wrong screw in a component could damage the unit.
  4. If the unit contains light-sensitive components such as toner cartridges, store the component in its original packaging or in a dark location to avoid damage.
RECOMMENDED INSTRUCTION FOR OTHER COMPONENTS ON SAME LAPTOP MODEL
  1. How to removal and replacement the Display Bezel for OMEN by HP 15-DG Series
  2. How to removal and replacement the Display Hinge Bracket for OMEN by HP 15-DG Series
  3. How to removal and replacement the Display Panel Assembly for OMEN by HP 15-DG Series
  4. How to removal and replacement the IR Sensor Board for OMEN by HP 15-DG Series
  5. How to removal and replacement the Display Panel for OMEN by HP 15-DG Series
  6. How to removal and replacement the Display Panel Hinge for OMEN by HP 15-DG Series
  7. How to removal and replacement the LED Board for OMEN by HP 15-DG Series
  8. How to removal and replacement the Battery for OMEN by HP 15-DG Series
  9. How to removal and replacement the RJ-45 Door for OMEN by HP 15-DG Series
  10. How to removal and replacement the Memory Module for OMEN by HP 15-DG Series
  11. How to removal and replacement the Power Button Board for OMEN by HP 15-DG Series
  12. How to removal and replacement the DC-IN for OMEN by HP 15-DG Series
  13. How to removal and replacement the Solid State Drive (SSD) for OMEN by HP 15-DG Series
  14. How to removal and replacement the System Board for OMEN by HP 15-DG Series
  15. How to removal and replacement the Webcam Module for OMEN by HP 15-DG Series
  16. How to removal and replacement the Base Enclosure for OMEN by HP 15-DG Series Gaming Laptop
  17. How to removal and replacement the Thermal Module for OMEN by HP 15-DG Series
  18. How to removal and replacement the Speakers for OMEN by HP 15-DG Series
  19. How to removal and replacement the 2nd Display Panel for OMEN by HP 15-DG Series
  20. How to removal and replacement the 2nd Display Support Board for OMEN by HP 15-DG Series
  21. How to removal and replacement the CU Plate for OMEN by HP 15-DG Series